Please read this first...

If you want to know what I'm on about in the shortest time then please read the introductory first post and my current action plan. Comments are very welcome. And if you like this blog, please tell a friend. Thanks!
Showing posts with label water. Show all posts
Showing posts with label water. Show all posts

Monday, 6 April 2009

Water efficiency has become a lifestyle

It's a significant day for my part of the world: for the first time in a hundred months our regional water storage capacity is above 50%. At its lowest in 2007 we had only 16.7% and the government was seriously considering the need to truck or ship drinking water in to sustain the roughly two million people in the immediate area.

Thankfully that worst-case scenario never eventuated, and there have been a number of rain events that have brought the levels up bit by bit. Most interesting, though, has been the success of water conservation programs.

Under the most severe restrictions residents were urged to target an average per-capita water use of 140 litres each day - an enormous reduction from previous norms of around 300. By the time dam levels rose to 40% in July last year, we had stayed below "Target 140" for 52 consecutive weeks. Consumption dropped to as low as 112 litres per person today in one week near the end of that period.

Reaching the 40% storage level was the trigger for easing of restrictions and the revision of our target to 170 instead of 140. And what do you suppose happened to our water consumption?



I've trawled through the weekly press releases to obtain the reported usage stats since Target 140 was introduced almost exactly two years ago and graphed them against the target at the time. Blue line shows water consumption per person per day against the red line which is the target in place at the time: 140 and 170 respectively. There are 66 weeks reported for Target 140 and 32 for Target 170, both with a couple of weeks gap over the New Year breaks.

Visually, you might think that with the relaxed restrictions our water use went up dramatically. But in fact, the averages for each target period are 131.8 and 138.3 respectively - still under 140 even with the higher target!

Very shortly we'll be operating under a Target 200 regime. It's my hope that Brisbane residents have taken the water conservation message to heart and will continue to keep their consumption well under the nominal targets.

Because despite all the good news, our State Government still wants to dam the Mary River and is building desalination plants that will be powered by burning coal.

Oh well, it's a start.

Sunday, 4 January 2009

Too much to say

Ironically, it's been quiet here because there's too much to talk about. Or maybe it's because there's been too much talk about.

Since I started doing this the world's attention has been brought quite sharply to bear on most of the issues that concern me. There's so much high profile discussion and activity going on that my little blog seems rather superfluous. Which is great!

I just want to highlight a couple of local bits of good news.

1. Brisbane folk are now habitually conservative with their water. We managed to meet the 140L/person/day target under extreme restrictions and even now that the dams are heading towards 50% capacity we're still sitting well under the 170L revised target. I just read my water meter for the first time in 201 days, and our total household usage over that period averaged only 194L per day - actually less than the previous six months when we were watching like a hawk.

2. Politics is (generally) swinging in the right direction for sustainable civilisation. The election of Obama is of course globally significant, but even here at home we've seen the Traveston Dam project put on hold, willingness to regulate agriculture in order to protect the Great Barrier Reef, plans for floating desalination plants shelved, proactive measures from government to promote energy efficiency and GHG reductions, community gardens... heaps of stuff.

3. The combination of environmental/sustainability concerns and the economic crisis is driving a swing away from "consumerism". I so hate being thought of as a "consumer". I want to be a "contributor". But anyway, it seems that I'm far from alone in my back yard garden tinkering, chook raising, material recycling and "waste not, want not" attitude. Newspaper articles are even using words like "frugality" in a positive lifestyle sense!

So here's hoping that 2009 continues in this trend. There will certainly be bad news this year (I predict a sudden resurgence in the price of oil at some stage, going even higher than the peaks of last year) but there is also an atmosphere of hope. As I heard it said on a BBC radio interview yesterday, a crisis is an opportunity for change.

Monday, 24 November 2008

Stats Update

Initial figures from the meter attached to the fridge are good. Including the initial cooling effort required after turning it on for the first time, it's averaged about 1.4kWh per day over the past four days. I've reset the meter this morning to correspond with reading all the other meters so I'll be able to build up a better picture of it over time.

The other energy figures are also good. For the past 39 days:
- PV generation up to 4.62 kWh/day
- Household consumption down to 7.88 kWh/day
- Export up to 2.26 kWh/day

We've had more than enough rain recently so the tanks are still supplying water for laundry, toilet and gardening. Hot water system needed boosting one evening during the rainy period but is otherwise cracking along in the spring sunshine. Our recent rates notice showed us maintaining a significantly lower consumption than our neighbours and so I haven't bothered keeping a close eye on the water meter.

Tuesday, 17 June 2008

Meter matters

Two real-life examples of why meters are your friend and reading them is a good idea.

1. "Where did our water go?"

We've had a lot of rain this month. Following a two month stretch during which a total of 26mm fell at our place, we had over 220mm in just five days. That's enough to fill our tanks four times over. With no room for more water, I decided to let any further showers flush out the internal dirty water diverters and opened up the valves. Then promptly forgot about it.

It rained twice more in the following three days: falls of just a few mm but enough that I expected to see the new inflows make up for the water we'd pumped out for the laundry and toilet. But for some reason the gauge didn't go up. In fact it was heading downwards at a surprising rate - around 10cm (800L) in two days. I figured we must have been catching up on a lot of washing.

Two days later we were down another 800L. Something finally triggered my memory - the diverter valves were open! I suddenly recalled that the internal hose which allows the diverter to drain to the outside is not watertight, which means that water from the main chamber can slowly leak out when the drain valve is opened. We must have wasted well over a thousand litres this way.

If I hadn't put a gauge on the tanks and made a habit of checking it, we'd have lost half our supply (the valves are about halfway up the tank wall) within a few more days.

2. "The bill is for how much?!"

A week ago as I sat here working in my home office I noticed somebody briefly inspecting our electrical meter box. "Ah," I thought, "our quarterly electricity bill will be turning up soon." Well turn up it certainly did!

With all that rainy weather I mentioned just before, we had to use the electric booster on our hot water system for a couple of days. Imagine my surprise when the total bill came in at well over twice what I'd been expecting, with an off peak consumption for the quarter of one thousand, five hundred and twenty six kilowatt-hours! The charge for that was almost as much as I'd budgeted for the whole bill.

I hadn't read the meters since a few days before it rained, so I rushed out to check them. After sitting on 90615.3 for about eight months, the off-peak meter today reads... 90638.1. A grand total of 22.8kWh difference.

That's actually more than I'd been hoping to see given how little we used the booster, but it's rather insignificant compared to the matter of the invoice. The meter for the constant supply had also been recorded incorrectly - even today, a week after the reading, I'm still 157kWh short of what they're claiming. It'll take us another 20 days to reach that point.

The lady on the phone conceded that it was a bit odd to have such a spike, although for some reason this bill is recorded as being an "estimated" value. She spent a long time conferring with a supervisor before agreeing that the meter should be re-read. The soonest they could get somebody here would be the 20th (I told them not to rush on my account - I'm in no hurry to get a bill). And she made it sound like she was doing me a favour not charging me the customary $24 fee for a repeat reading (like hell I'm going to pay for them to fix their screw-up).

Ah well, I probably won't be paying too many more bills to that company anyway. I was already looking into switching retailers to get a better rate for the energy my PV panels will produce - 20c instead of 14c per kWh. And once that gear's installed you can bet I'll be watching the new meter closely indeed.

Thursday, 29 May 2008

More water, but it's all cold

Good news: it's raining again and the tanks are now over 50% full with more falls forecast for this weekend.

Bad news: combined with the lower temperatures and reduced sun intensity of winter, the persistent cloud has forced us to switch on the electric backup for our solar hot water system. It's been seven months since the electricity company saw that meter move.

Ah well.

Saturday, 24 May 2008

Stats Update

It's 19 days since my last stats update, when the tank levels had fallen so low I switched the washing machine and toilet back to using mains water. I had calculated at the time that we had been using about 250L/day of tank water plus almost 200L from the mains. It's no surprise then that our recent mains consumption has been...

409L/day.

More than we were using over summer, but back then we had #3 in disposable nappies and now we're washing cloth ones almost daily. Less than I estimated we were using in the previous period... we are probably a bit more diligent with our conservation knowing we're back on mains supply.

After a month of zero rainfall, last weekend delivered a lovely little squall and dumped 14mm on us in under an hour. Approx 2.2kL added to the tanks, around 30cm above empty now. With the prospect for winter rains looking grim I switched the toilet back to tank water but left the washing machine on mains.

Power consumption for the past few weeks fell to the second-lowest reading this year: 7.3kWh per day (304W continuous).

Saturday, 19 April 2008

Stats Update - now including tank water

Here are the latest stats for our electricity and town water consumption over the past 25 days, plus some new information on our tank water use.

Electricity consumption has increased again.
This period: 8kWh per day, or 333W continuous
Previous 21 days: 6.84 and 285
Average since start of year: 7.62 and 317.

Town water use is also up. I think it's largely my fault... love the hot showers in cooler weather. 189L/day vs 130 in the previous 21 days and 164 average since the start of the year.

I may have mentioned when I was planning my tank installation that I considered getting a water meter to measure how much water we pumped from the tanks. Well I didn't do that, but I did fit a water level gauge which shows the height of the water in increments of 10cm. I also bought a rain gauge at the start of February and started keeping records of daily rainfall, and I noted on which date my tank was last filled completely. I've observed that 1mm of rainfall causes a rise of 20mm in the tanks and I've calculated that 100mm of water in the tanks is very close to 800L.

Armed with all this information and the current gauge reading, I can estimate how much water we've used and when it's likely to run out. In the 21 days since last full the tank level has dropped from 110cm (full) to 70cm. Rainfall of 11mm has added about 22cm to the tanks, so we have extracted about 62cm in total. That works out to about 4960L, or 236L/day. At that rate we have enough water to last another 24 days without further rain and a full tank would give us 37 days supply in a dry spell.

What's startling here is the overall amount of water we're using... 189+236=425L/day. It's quite a bit more than before we had the pump installed but we aren't using any significant amount of water outside. That means we're using more inside.

The laundry has to be the main culprit. Once we had the washing machine hooked up to the tanks we started using cloth nappies for our infant instead of the evil but water-efficient disposables. So every day or two we now go through a big bucket of tank water for soaking and then an extra load of washing. Combine this with my slackening frugality in the shower and you would probably account for most of the roughly 100L/day increase compared with figures from six months ago.

Sunday, 9 March 2008

Stats Update

For the two weeks to 4th March:
Electricity averaging 7.51kWh per day (313W continuous)
Water averaging 188L per day

Averages for the quarter since Dec 28 are 7.72kWh (322 continuous) and 165L.

Thursday, 7 February 2008

Wet wet wet

I bought a rain gauge a couple of months ago. Managed to resist the impulse to start making daily records. Well, up until a week ago, anyway.

The way our gutters are set up, we can capture the rainfall from about 160 square metres of roof. That means for every millimetre of rain in the gauge about 160L flows into the tanks.

Over the past five days we've had 90mm of rain. That's almost fifteen thousand litres!

Beyond just my own backyard, the whole region is breathing a little easier with significant flows into our water storage dams. From a low of around 17% late last year, storage has almost doubled to around one third of capacity.

Saturday, 26 January 2008

Stats Update

Average daily consumption for the past 29 days: 7.56kWh of electricity, 160L of town water.
Rainwater in storage: approx 6.4kL.

Per-day stats are one way to think about consumption of resources, but it's a bit of a mental leap to associate those numbers with our actual behaviour. I've started another column on my spreadsheet which puts the electricity use into a different perspective, converting it to an average continuous load.

Our 7.56kWh/day figure is equivalent to using 315W continuously - like having five of the old 60W incandescent light bulbs (or the common halogen downlights) burning day and night.

Tuesday, 8 January 2008

Stats Update

Our mains water consumption for the past 11 days has averaged out to...

187L per day!


That's the total for the five of us, not per person. This is in line with the drop I saw in the last readings period after the tanks were connected to the laundry and toilet. Looks like sub-200 territory is here to stay, at least while there's water in the tanks.

With that qualification in mind, I'm going to start reporting our tank reserves along with these stats. With a specified minimum diameter of 2.2m and a current water height of 110cm in two tanks, we have approx 8.3kL in storage.

Looking at electricity, our hot water system narrowly avoided needing a boost late last week. I had a shower one evening in water that was merely "warm" but with a pause in the rain the next morning the temperature quickly went back up into "ouch" territory. Tariff 33 consumption remains at 0kWh.

Our general consumption is definitely up a bit from the previous trend though. The water pump would be contributing to that. We're using fans to keep ourselves cooler in the warm weather. And maybe we've slacked off a bit with turning things of and generally being frugal. For the past 11 days Tariff 11 usage has averaged 7.4kWh per day.

Just for comparison, here's a graph of our average daily usage per quarter (as per the electricity bill) for the past two years or so. The final column represents the current usage. Would love to get that blue bar down significantly but I'm not sure how I can do that without tossing out the fridge and not cooking food any more.

Pipes and Pumps, part 3

I've recently stumbled across the controversial figure of Amory Lovins, a high-profile American advocate of radical energy efficiency improvents through integrative design, improved technology and really obvious (once they're pointed out to you) common-sense actions. In March 2007 Lovins gave a series of five evening lectures at Stanford University and these are available for free download as podcasts through iTunes. I found these less than a week after my pump had been installed... and boy did I wish afterwards that those two events had occurred in the opposite order.

In the Tuesday night lecture on improving energy efficiency in industry, Lovins focused fairly heavily on pipes and pumps. Apparently a very large percentage of the electrical energy used by industry is consumed in the motors of pumps. The point is made that due to the compounding energy losses between electrical generation (usually in a coal-fired power station) and consumption in the motor, even a relatively small improvement in end-use efficiency will be multiplied back through the chain to deliver a far more significant drop in generating capacity requirements and associated pollution emissions etc.

In the pursuit of those end-use efficiency improvements, Lovins laid down a number of basic principles for designing energy-efficient pumping systems. I encourage you to watch the lectures for yourself, but my quick summary would have to include:

- If pipework looks neat, it's probably inefficient
- Short, fat, straight pipes are far more efficient than long, thin pipes with corners in them
- Engineers tend to optimise pipes and pumps separately focusing on up-front cost, when an overall cost reduction can be achieved by optimising them as a system for efficiency
- By optimising the efficiency of the system you can specify a much smaller pump which costs far less to buy, run and maintain
- It's usually best to design the pipework *first* and then lay out the equipment around them

That first point especially hit home. Have a look at the pictures in the previous post or two - I actually insisted that the installer do a "proper" job and fit two additional 90-degree bends in the pipe that takes water to the toilet instead of allowing it to curve smoothly (but untidily). I'm quite sure that if I'd watched this lecture beforehand I'd have spent some time carefully designing and specifying the pipes and pump which are going to be a fixture of our home for some years to come.

Oh well. On the bright side, check out the water use stats I'm about to publish in a separate post.

Saturday, 29 December 2007

Pipes and Pumps, part 2

The good news is that in terms of reducing our use of town water, this project is definitely meeting its objectives! We've done piles of washing and started flushing the loo again with wild abandon. I even hosed off the concrete along the back of the house after doing some top-dressing of the lawn. With the weather we've been having lately (lots of showers) we've been unable to get the water level more than about 1200L below capacity, and as of this morning the tanks were full again. Makes me wish there was some way to use that water for bathing as well.

However... all this water abundance has come at the cost of increased electrical consumption. Of course I knew that some electricity would be necessary to power the pump, but I've discovered two ways in which our setup is far from optimal.

First, the pressure switch. That blue gizmo on top of the pump which monitors the pressure and decides whether the pump needs to be running or not. Courtesy of my power meter I have discovered that the cost of monitoring the pressure is apparently about 15W continuous power consumption, or the equivalent of one rather bright CF bulb shining 24x7. In most homes that would be considered negligible, but in my home that's slightly more than a 5% increase in our average daily energy use.

The obvious solution to problems of that sort is simply to switch off the device when it's not needed. And sure, the pump needs an appropriate switched outlet to plug it into. But that would only solve part of the problem.

Three out of the four taps fed by the pump are used in such a way that it makes sense to switch on the pump before use and switch it off again afterwards - doing a load of washing, filling the tub or a bucket, using the hose and so on. The toilet, though, is a different matter.

With a toilet you need the water to flow into the cistern after your, um, "activity" is completed, and then only for a relatively short time. Can you imagine being required to flush, wash hands, walk to the laundry, flick the switch on, wait 30 seconds then flick the switch off again? Can you imagine teaching young children to do that? No, a simple switch is not going to suffice here.

The next most obvious suggestion is to install a second switch in the toilet, wired up in a 2-way configuration like many light fixtures are - such that flicking either switch up or down will change the on/off status of the light, or pump in this case. It would alleviate the walking part of the problem, but you'd still be left with the waiting.

What I'm hoping to do is a variation on that idea using a logical "OR" operation and a time delay switch. This switch is normally in the "off" state. When you push it in, power is allowed to flow but only for a minute or so until the spring-loaded mechanism returns to its initial position. So you push one button on the cistern to flush the toilet and then another button on the wall to refill the cistern, then you walk away (to wash your hands, of course). Either the laundry switch OR the toilet time delay switch can be independently activated to provide power to the pump as required.

Actually both of those switches will feed into the exterior switched socket that the pump is plugged into, so the correct logical expression is: (laundry OR toilet switch turned on) AND (external switch turned on) -> (a powered pump).

I foolishly bought all three switches today without first asking about the prices. Total cost $106. Could have saved twenty bucks if I hadn't asked for the laundry switch to have one of those little red lights in it to show when it's turned on. But anyway...

At current prices of 21.455 cents per kWh (15.455c regulated tariff 11 plus 6c GreenSwitch renewable energy premium) I'm going to have to have the pump switched OFF for about 33 thousand hours - nearly four years! - to recover the cost of the switches alone. But then I'm still predicting that energy costs will rise rapidly over time, and hopefully these switches will be in use for a long time after they've paid back their cost.

The moral of the story is to carefully check the electrical requirements of the equipment you're installing in a bid to save water. Thus endeth part 2. Next time I'll look at the other, far more important aspect of the energy efficiency equation when it comes to pumping water around: the pipes.


(Got any ideas about how to design a really efficient tank/pump system for home? Please share in the comments.)

Pipes and Pumps, part 1

Can you think of a more boring-sounding subject? There wouldn't be too many, but if you care about energy and water efficiency then there are some very important things to know about pipes and pumps. As with many lessons in life, I learned these things shortly after the precise moment when it would have been most helpful to know them.

The context is, of course, that having installed tanks to capture the rain that falls on my roof I needed some way to get that water into my laundry and toilet in order to reduce my consumption of externally-supplied water. In this time and place carrying water in buckets is not an acceptable solution. Pipes, valves and a pump would be required. In this post I'll show you the solution we installed.

As I've mentioned more than once, our two tanks are situated one at each end of our house and are connected by a 25mm plastic pipe at ground level. That pipe has two functions: it allows the water level to rise evenly in both tanks regardless of how much water flows through their respective downpipes, and because it runs straight past the laundry it allows water to be drawn evenly from both tanks through a T piece inserted at the appropriate point. So far so good.

Knowing my limits, I paid a professional to supply and install the rest of the solution. We had a brief discussion about my requirements, agreed to use a pump at the low end of the price/performance curve and arranged to install four taps: one on the outside laundry wall adjacent to the pump, two just inside the laundry for the tub and the washing machine and the fourth a few meters along and through the wall for the toilet.

Stop! Camera time. In this first image you can see the inlet (low foreground) going into the pump body (red). On top of the pump is the electric pressure switch (blue) which turns on the pump whenever the outlet pressure drops below a preset level. The water flows upwards through the pressure switch and out the top.


Here you can see the new pipework (black) going up the wall to the new tap (left) and still further up then through the wall into the laundry.


Next, a shot inside the laundry with the double tap arrangement for the tub and washing machine.


Finally, our modified toilet. My original plan was to have a second tap in the toilet just as we have in the laundry so that we can connect the cistern to the appropriate one as required. The bloke we hired to do the installation explained that council regulations wouldn't allow it - something about making it too difficult for the elderly or the disabled to ensure reliable toilet operation - and so we now have a permanent dual-float configuration where we merely need to turn on the appropriate tap. The tap (and float) on the left control the existing mains water supply while the parts on the right take water from the pump.



Now I shall be the first to admit that, overall, this isn't a "pretty" job - because that really wasn't a goal. The pump gets hidden under a plastic cover that's about the same colour as the concrete, the laundry is destined for eventual renovations anyway and the whole lot is down the back side of the house where nobody goes looking for aesthetic satisfaction.

So that's what it looks like. In the next post I'll go into how well it works.

Friday, 28 December 2007

Stats Update (Updated)

I last read my electricity and water meters 37 days ago. Some interesting things have happened between then and now including the installation of the electric pump that enables us to use captured rainwater in our washing machine and toilet. There'll be a separate post about the pump and related matters, but I have been very curious about how much impact that system would have on our consumption of external energy and water.

Today's reading won't give the whole story. For one thing, I can't recall exactly when the pump was installed but I'm pretty sure it was after that last reading. And our whole family went away for a week's holiday during the period so our consumption was artificially low during that time - I'll do some math to compensate for it but even that won't be accurate because the fridge was running for the week and I don't know how much power it would have used when nobody was opening it.

And speaking of the fridge... it's not well. Either it has a blocked drainage channel or leaking door seals. There's too much Christmas food in it to try and fix the problem right now but I wouldn't be surprised if it's using more power than usual. (Update: only hours after I posted that, the electrical safety switch in our fuse box tripped. The fridge was the culprit - all that water building up must have short-circuited something. Emptied it out and pulled it apart a bit, found the decomposing remains of some corn kernels blocking the condensation drainage pipe. Cleaned, reassembled, tested, OK now.)

So then: Tariff 11, the standard domestic electricity supply. Over 37 days we used 265kWh, averaging about 7.15kWh per day. (Our average for the 94 days to 10 Dec, which includes our week away, was almost exactly 7kWh.) Compensating for our time away brings the figure to more like 8.8kWh per day, a fairly significant increase. I'll have to do some work here to understand where the extra power is being used. Probably I'll connect the fridge and the pump to my two power meters and find out precisely how much of a contribution they're each making.

Next up is Tariff 31: Night Rate. I'm including this one just for comparison, because since the installation of our solar water heater we've switched to a different tariff. But energy is energy, and on this bill we see that over 21 days we used 90kWh. This included a few days where we had no hot water system at all and then a few more after the solar system was installed but before the electricity company came to reconfigure our meter for the other tariff.

Tariff 33, "Controlled Supply", works similarly to the night rate system except that it's available for 16 hours each day instead of just 8. I decided that made more sense for a hot water booster because we'd likely need it in the late afternoons and evenings when night rate supply would still be unavailable. Our total consumption over the 73 days covered on the bill was...

2kWh. That's not per day, that's total. We had to flick it on for an hour or so sometime in October if I recall correctly. It hasn't been on since, so of course the consumption over the past 37 days is a flat zero. I love my solar hot water system.


OK, so on to the water. I want to put this into perspective.

For the previous 39 days (that is, prior to the last time I read the meter) we had averaged 381L per day. For the 37 days just ended our daily average is 200L per day!

Even taking out the week we weren't here gives a figure of 247L per day. Again this is something that will need some monitoring during the coming weeks to work out our ongoing rate of consumption but I'm pretty pleased about that. Tank water is now being used for all outside requirements, all laundry, and most of our toilet flushing. The Shower Saver would account for a sizeable reduction in mains water use as well.

Monday, 12 November 2007

Water under control

A couple of weeks back I was shocked to see that over a ten day period our water use had shot up to 507L per day, on average. Since then we've renewed our vigilance and made a real effort to get water use back down to where it had been.

The results are satisfying. For the two weeks ending this morning our average consumption is back down to 320L per day, which is slightly better than where we were tracking before.

Helping the cause is our new Shower Saver. I can't imagine using it much in winter, but what a brilliant idea this is. Every shower should have one.

Also, our water tanks are full and overflowing! With all the recent rain there's not been much need for outdoor water use, so I'm eagerly awaiting a call from a mob to come and quote on installing a pump and some internal taps for the toilet and washing machine. I'm really looking forward to seeing how low our mains water consumption can go once those are hooked up.

Saturday, 3 November 2007

Maths Problem

Solve:

A man has two identical water tanks of diameter 2.2m. Mere moments after connecting the downpipes to catch rainwater, the heavens open up and the tanks fill to a height of 0.8m. If the tanks have a combined capacity of 10,000 litres, how much higher can the water rise before it starts to overflow out the side of the tanks where no drain pipe currently exists, quite likely causing serious damage to the compacted rock dust foundation on which the tanks are sitting?

Answer:

Not bloody far enough! The bottom of the overflow outlet is less than 1.2m higher than the base of the tank, meaning the tanks are about two thirds full after just one night's worth of moderate rain and a couple of showers.

A bit of quick pipe work by my helpful neighbour (the one who installed the downpipes without the drainage in place, saying it wasn't going to rain soon enough to be a concern...) has now mitigated the threat. Any overflow will now be channelled a few metres away over the lawn where it can't cause any major trouble. Proper drainage to the street is a project for another day.

The next question is what to do with around 6,500 litres of water, given that I don't yet have a pump or any plumbing to take water into the laundry and toilet where it's needed. Thankfully the answer doesn't require a calculator: time to go pump shopping.

Saturday, 27 October 2007

A productive day!

  1. Tank interconnecting pipe fitted: check.
  2. Overflow outlets fitted and sealed: check.
  3. Water level gauge fitted and calibrated: check.
  4. Custom gutter cleaning tool designed and fabricated: check.
  5. Gutters cleaned, probably for the first time in a decade: check.
  6. First flush diverters emptied ready for the next rains to rinse out the dirty gutters: check.
  7. Beer bottles emptied: check and check.

That's everything I'm willing to do myself. From here on I'm paying somebody else to finish the job. We've got overflow pipes to run underground to the street, a pump to install and internal plumbing to be done.

Well actually there's one more thing for me to do, which is to bury the connecting pipe that runs between the tanks. That can wait until after somebody has installed a t-piece in the middle of it for the pump to draw from.

Instead of a rubber... thing... to seal the overflow outlet I bought two 90-degree flanged fittings and just screwed them onto the outside of the tank with silicon to seal them. They point downwards and the insect barriers just pop onto the end of them. More pipe can be attached later to take any overflow safely away.

Friday, 26 October 2007

Ebb and flow

Over the past 24 hours my attention has switched from finding missing water to managing unexpected water. We've had some short but heavy showers and something that could reasonably be called a storm, and so it is that my tanks are finally being put to use.

As best I can tell, the southern tank has about 20-30cm of water in it and the northern one about 30-40cm. If that's right then we've caught a bit over two thousand litres. It would have been substantially more in the northern tank if I'd managed to clean out the gutters before the rain came. But I didn't, and debris clogged up the pipe causing the water to back up and flow over the sides.

I'm pretty excited about having water in there, even though we can't actually use any of it yet. It's not high enough to come out of the bucket taps and I don't have any pipes or pump connected to the ground-level outlet. Still some work to do.

This weekend I have two tank tasks which must be completed. I need to get a rubber... thing... to properly seal the overflow outlets, and I need to clean the gutters. I'd also like to fit the gauge which I got replaced today, and if everything's really cruising along perhaps put in the connecting pipe.

And in the back of my mind I still have to figure out why we're using so much more water recently. Going to be a wet weekend, at least in my head.

Thursday, 25 October 2007

Water update

Two days have passed since the discovery that our household water use had shot up unexpectedly. I just read the meter again: an average of 424L per day for the past two days. That's better than 507 over the previous ten but still well up on our previous benchmark of under 350.

To test the idea that maybe our new water heater was wasting a lot of water by being over-heated, I placed a bucket beneath the overflow pipe. There's water there, for sure, but it's nowhere near the missing 75L per day. After two sunny days the bucket is about half full - we can use that water safely on the gardens so I don't have any real concern about that.

So we come back to the possibility of a leak, or a change in our behaviours. We'll focus on the behaviours first, maybe keep a log of our water use activities during the day. I'd really like to get those figures back to where they were without having to pay a plumber.